@juancl, let us have our Second Level Support Team to check on your case further. I can install the printer (clean install) and it will install and can be accessed by my MacOS but bonjour and AirPrint services are not available. No error message it just keep trying to connect until it stops and say it could not connect. My network appears listed (so it detects it) asks me for the pwd to connect. I have an RE7000 connected via ethernet to my EA9500 router. It get stuck on Step 7. I have a wrt3200acm installed with a wire re7000 connected as an access point. When I look at a device listing on the re7000 I can see the printer (hp8620) but it cannot be added to my printers available on my MacOS. If I configure for extender I can only configure 2.4 using WPS. By the way, may we know your network topology? Yep those are steps. I also have an hp8620 printer installed that seems to be connected to the re7000 but is not recognized by the wrt3200acm. Wifi have diffeernt passwords and the 5 does not broadcast SSID. All I have is the new modem/router Arris TG3452 which provides a 2.4 GHZ and a 5 GHZ wifi. Shoot us an email at Linksyscares@linksys.com with the following information: Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type. I the RE7000 firmware up to date and the operational mode set to access point? I have several old wireless routers configured as access points. I've configured Re7000 as an extender but when I try to configure as an AC (either thru the change option on setup screen or in initial setup after a reset), the light remains a blinking amber "forever" and the device is not recognized. The RE700 would not connect … On behalf of your concern, you might want to follow the troubleshooting steps: - Please reset reconfigure your RE7000 as a Access Point: http://www.linksys.com/us/support-article?articleNum=187985, http://www.linksys.com/us/support-article?articleNum=187984. This extender can also be setup as an access point allowing you to connect a router using a wired connection to boost the most broad bandwidth input possible. I have managed to circumvent the problem  by assigning a fixed IP address to the printer and after a few restarts, it appears the connection remains and I have access to both Bonjour and Airprint. You might wanna check out this link: https://www.linksys.com/us/support-article?articleNum=187986. Yesterday my provider changed my modem for a newer model Arris TG3652 and configure it with the same names and passwords for my networks. Update us after. Page 13 Enter password for main network. I also have an hp8620 printer installed that seems to be connected to the re7000 but is not recognized by the wrt3200acm. I want to maximize the advantages of this setup (maxstream, etc.). One other thing which may be relevant. I provide the password and then it tries to connect, and keeps doing so for a while until it tells me it could bot connect to it. When I research the issues, it appears this printer is NOT visible to the router. I just got an RE7000 to test replacing them (and hopefully getting a stronger signal as well as 5ghz band). Page 12 Range extender or access point? Your extended wireless network. I just got an RE7000 to test replacing them (and hopefully getting a stronger signal as well as 5ghz band). Connect your Wi-Fi devices to the extended network you just created. Have had an RE7000 for a year or so. Linksys RE7000 review: Performance. http://www.linksys.com/us/support-article?articleNum=135206. Yesterday my provider changed my modem for a newer model Arris TG3652 and configure it with the same names and passwords for my networks. SO, my question is, if I have a device attached to the re7000 why isn't it visible to the wrt3200acm. Page 14: Setting Up As Wired Range Extender (Access Point) 5. Since the RE would extend your Greenwave wireless network you might want to probably change the security type to WPA2 Personal and add an 8-12 password characters just to isolate security issues with the RE and the Greenwave before setting up the RE7000 with your wireless network. Is there an error message you're receiving while setting up the range extender? Linksys says this extender will work with all WiFi routers so you don't need to adjust any settings to get this working alongside your current setup. https://www.linksys.com/us/support-article?articleNum=187986. I would like my network to have one SSID for the router and the extender, like an enterprise type setup. Worked perfectly as an extender for my 2.4 and 5. You are going to be able to extend both bands 2.4 Ghz & 5Ghz. Please make sure to manually input the password. I have a wrt3200acm installed with a wire re7000 connected as an access point. Wrt3200ac and re7000 installed as access point. Unable to configure RE7000 as an access point. Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type. Hi, juancl. The issue I am having is my HP 8620 is connected to the extendeer (R7000) and is NOT visible to the rounter (wrt3200acm). The RE700 would not connect after the modem change. For some reason, it won't allow me to use the bonjour features (wireless scan) and airprint reliably. I have several old wireless routers configured as access points. P.S. I may have found the solution to my problem (though it doesn't answer my basic question). When I do a network scan through smartmwifi, the printer does not show up. Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type. When I turn the RE7000 off, the printer connects to the main router AND i have access to bonjour and airprint features. Router is a Greenwave FIOS-GT-1100-FT which serves as a cable modem connected to a Verizon -- now Frontier -- FIOS network (if it weren't for that, it would probably be Linksys -- but that's another story). If (as manual suggests) I try to configure the 5.ghz using WPS, I get the same kind of thing -- hangs for ever with a blinking amber. Worked perfectly as an extender for my 2.4 and 5. When I do a network scan through smartmwifi, the printer does not show up. I have a similar installation for a canon printer and it connects properly (recognized by wrt3200acm) and I can use bonjour and AirPrint. Kindly check if there's a step that you've missed. Choose a network to extend. Any thoughts on how to make this thing work? Try to reset the extender to factory defaults and set it up again. Tried resetting and when I go through the configuration process it finds my network, I enter the password and it just keeps trying to connect but cannot. Have had an RE7000 for a year or so. I did reset the extender a couple times.

.

Logan Valley Mall Events, Walmart Singer 9960, Ornamental Pineapple Plant Drooping, Can You Get Sick From Curdled Milk, Integrated Process In Marketing, Monarch Specialties Corner Desk, How To Cook Imitation Crab In The Oven,